Things you should know about Polycarbonate Sheet, Sheets and Panels
A common misconception is that ‘all polycarbonate sheets are the same’. This is not true, as a matter of fact, it is far from a fact. While most manufacturers of polycarbonate sheets start with a similar base resin, this is where the similarities normally stop. Most polycarbonate sheet extruders run a base material far different from what the standard has been for the last 30 years. Most polycarbonate sheet is now made without the flame rating it had in the past. Polycarbonate Sheets are sometimes called ‘polycarbonate panels’ or ‘polycarbonate plates’, they are still made from the same high quality resins. One of the best known manufacturers of Polycarbonate resins and sheets is Sabic Polymers®, the manufacturers of Lexan® resin and Lexan® Sheet products. Over the last several years, Sabic has quietly discontinued the UL ratings on their Polycarbonate.
Industrial Plastic Supply And Tuffak GP (formerly Makrolon GP)
For more than 30 years, Industrial Plastic Supply has relied on the high quality Polycarbonate Sheets produced by Sheffield, now part of Plaskolite (formerly Covestro and Bayer MaterialScience). Plaskolite produces a crystal clear, ultra high impact strength polycarbonate resin, this Makrolon resin is the finest in the industry. Plaskolite has also chosen to continue to produce this high quality material in general purpose, and the Tuffak GP meets the UL 94 V-0 rating, the only supplier to continue this expensive, but extremely valuable service. Take a moment and look at your requirements, see if perhaps somewhere on the blue print is a note that states your polycarbonate material needs to be UL 94 V-0 approved or rated. If so, Tuffak GP is your only and best choice!
How is Plaskolite Tuffak GP Polycarbonate available
We stock Plaskolite (formerly Covestro – Bayer MaterialScience) Tuffak GP in flat panels, considered Polycarbonate Sheet or as Polycarbonate Sheets. We can cut theses sheet Polycarbonate materials to strip or strips, blocks, or just a cut to size piece. At Industrial Plastic Supply we have stocked large quantities of these materials, and continue to keep Tuffak GP (formerly Makrolon GP) and Tuffak FI (formerly Makrolon FI) sheets in stock. With a wide range of thicknesses ( .030″ – .500″ thick) and sheet sizes of 48″ X 96″, 60″ X 60″ and 72″ X 96″ as standard in .118″ – .500″, we can fill all your requirements.
Why you should use Plaskolite Tuffak Polycarbonate Sheet
Superior clarity, quality, surface finish, flame retardant and full USA factory technical assistance are just a few reasons. Buying polycarbonate sheets imported from somewhere half way around the globe, from an unknown manufacturer with little or no technical support can be very risky. Plaskolite (formerly Covestro/Sheffield) manufacturers this premium quality polycarbonate sheet right here in the good old USA, in Sheffield, Massachusetts. They produce this crystal clear sheet on the latest and most technologically advanced extruders available, and have several warehouses for us to get material quickly for you. Why settle for an unknown? Can you afford to ‘try’ the other guys? Step up to the finest quality, and yet still competitively priced polycarbonate sheet, get Plaskolite Tuffak GP Polycarbonate Sheet(formerly Covestro Makrolon GP) for your next project. Industrial Plastic Supply also carries the Westlake Zelux M Polycarbonate Sheet and Zelux W Polycarbonate Plate. The Zelux M is a machine grade Polycarbonate Plate from .375″ – 4″ thick sheet, and the Zelux W is a clear – Window Grade thick Polycarbonate Plate in the same thickness range. Contact us for more information on this thicker material. We also supply other manufacturers grades of Polycarbonate Plate, including, but not limited to: Ensinger Plastics, Nytef Plastics, Rochling Plastics and more. Contact us for more information or technical assistance on Polycarbonate or any other quality plastic sheet, rod or tube. Call us at 866-832-9315 or send us a quick note here. Google+